Average daily range (ADR) is the mean distance between a stock’s high and low over a set number of sessions. Traders usually express it as a percent of price, so a $100 stock that typically trades $3 from high to low has an ADR of 3%. It answers a plain question: how much does this stock normally move in a day? That number shapes where a stop can sit, how many shares a fixed risk allows, and whether a quiet stretch is unusual for that particular stock.
How to calculate ADR percent
Take each completed daily bar, subtract the low from the high, and average those ranges over a window of sessions. Ten and 20 sessions are common choices. To express the result as a percent, divide each day’s range by that day’s close before averaging.
| |
Use the same window every time you compare. A three-day ADR swings around too much to tell you anything; a 60-day ADR reacts too slowly to show a base tightening.
ADR compared with ATR
Average true range (ATR) uses the true range instead of the plain high-low range. True range is the largest of three values: today’s high minus today’s low, today’s high minus yesterday’s close, and yesterday’s close minus today’s low. That captures overnight gaps. ADR ignores them.
For a stock that rarely gaps, the two numbers are close. For one that gaps often, ATR reads higher. ADR tells you how much room price uses within a session. ATR is closer to how far price can travel against a stop between one close and the next, so it is the more conservative figure when you set stop distance for a multi-day hold.
What a useful ADR looks like
A large, slow-moving company might average 1–2% a day, while a fast-growing mid-cap can average 4% or more. Neither is better. A wider range means more potential movement, but also a wider stop and fewer shares for the same dollar risk. A very narrow range may not move far enough to pay for the trade.
The more useful comparison is a stock against its own history. A stock that normally ranges 5% a day and has spent the last two weeks ranging 3% is contracting, even though 3% would be a busy day for a utility.
How TraderSight measures daily range
TraderSight’s tightness score uses the same raw input: the mean daily high-low range on completed bars. It divides the average range of the last 10 sessions by the average range of the 40 sessions before that. A ratio of 1.0 scores 0, a ratio of 0.5 scores 100, and the scale is linear between them. A ratio of 0.8 scores 40, the minimum for Tightening, and 0.75 scores 50, the minimum for Ready.
Because it is a ratio of the stock to itself, a volatile stock and a quiet one can both score well if each has narrowed relative to its own baseline. The score uses the plain high-low range, not true range, so overnight gaps do not count toward it. Range is also used as a guard: a stock whose recent range is a tiny fraction of its price, especially after a large gap, is treated as pinned by a pending takeover and invalidated. The full rule set is on How TraderSight works.
A worked ADR example
A stock trades near $80. Over the prior 40 sessions its average daily range was $3.20, an ADR of 4.0%. Over the last 10 sessions the average range was $2.24, an ADR of 2.8%.
- Ratio: $2.24 / $3.20 = 0.70
- Tightness score: (1 − 0.70) / 0.5 × 100 = 60
That clears the tightness condition for Ready. The stock still needs a trend score of 75 or more and to sit within 5% of its prior 252-session high.
A trader plans a buy-stop at $82.10, just above the tight range, with a stop at $79.50 below its low. The risk is $2.60 a share, slightly more than one recent daily range. With a $50,000 account and 1% risk ($500), that allows 192 shares (500 / 2.60 = 192.3, rounded down), a position of $15,763.20. A stop set two baseline ranges below the entry ($6.40, at $75.70) would allow only 78 shares. The position size calculator runs the same arithmetic.
Common ADR mistakes
- Ranking stocks by ADR alone. A high ADR is not a quality signal. It only says the stock moves a lot.
- Placing a stop inside one daily range. A stop closer than a normal day’s movement is likely to be hit by ordinary noise.
- Ignoring gaps. ADR understates risk for stocks that gap. Check ATR, and the chart, before trusting a tight stop.
- Treating a collapsed range as perfect tightness. A range near zero after a big gap is usually a takeover pin, not a base.
- Changing the window between comparisons. Compare the same number of sessions each time, or the change means nothing.
After-close ADR checklist
- Note the stock’s ADR over the last 10 sessions and the prior 40.
- Check whether the ratio is below 0.8, and ideally 0.75 or lower.
- Compare your planned stop distance with both ADR and ATR.
- Size the position from the stop, not from a share count you like.
- Read what makes a setup tight and the VCP screener rules to see how range fits with volume, trend, and distance from the high.