Glossary

Base Depth: How Far a Stock Corrects Inside a Base

Base depth is the percent decline from a base's high to its lowest low. How to measure it and why shallow and deep bases behave differently.

Base depth is how far a stock falls inside a base, measured as the percent decline from the high where the base began to the lowest low within it. A stock that tops at $50 and pulls back to $42 before recovering has a base 16% deep. Depth tells you how much damage the correction did, how much ground price has to recover, and how many recent buyers may be sitting on losses near the old high.

How to measure base depth

  1. Find the left-side high. This is the peak where the stock stopped advancing and the base began.
  2. Find the lowest low inside the base. Use intraday lows or closes, but use the same one every time.
  3. Divide the difference by the high. Depth = (left-side high − base low) / left-side high.
1
depth % = (base high - base low) / base high x 100

For a volatility contraction pattern, measure each pullback inside the base the same way. The first is usually the deepest, and each later one should be smaller.

Shallow bases compared with deep bases

A shallow base means sellers could not push the stock far, which often reflects steady demand. It also means price does not need to climb much to reach the high again. Flat bases, with a total depth near 15% or less, often form after an earlier breakout.

A deep base means more damage. The recovery math is unforgiving: a 20% decline needs a 25% gain to recover, and a 40% decline needs about 67%. Holders who bought near the top may sell as price returns to their cost, so the right side of a deep base often stalls just below the old high. Deeper bases are more common during broad market corrections, so check market breadth before judging a stock’s base in isolation.

How TraderSight treats depth

TraderSight does not score base depth directly and does not label where a base begins. Two measurements capture much of what depth implies:

  • Proximity to the high. The proximity score is 100 minus 500 times the percent below the highest high of the prior 252 sessions. A stock 5% below scores 75, the minimum for Ready. At 20% or more below, it scores 0. A stock sitting near the bottom of a deep base scores low until it has recovered most of the decline.
  • Range contraction. The tightness score compares the last 10 sessions’ average daily range with the prior 40. A base that has gone quiet near its high scores well.

The trend rules also matter. A deep correction usually drops price below the 50-day average, and a close below the 50-day marks the setup Invalidated. It is scored fresh once it recovers.

One limit: the 252-session high is not always the left-side high of the current base. If the stock’s yearly peak came earlier and higher, proximity is measured from that older peak.

A worked base depth example

A stock peaks at $120, which is also its highest high of the prior 252 sessions, and corrects to $93.

  • Total depth: ($120 − $93) / $120 = 22.5%
  • Second pullback: $112 to $101, which is 9.8%
  • Third pullback: $116 to $110.50, which is 4.7%

The pullbacks shrink from left to right. With price at $110, it is 8.3% below the high, so proximity scores 58. At $116, it is 3.3% below, so proximity scores 83 and clears the Ready threshold, provided tightness and trend also qualify.

A trader who uses the final contraction high of $116 as the pivot places a buy-stop at $116.20 and a stop at $110.20, just under the last low. The risk is $6.00 a share. With a $40,000 account and 1% risk ($400), that is 66 shares (400 / 6.00 = 66.7, rounded down), a $7,669.20 position. TraderSight would only mark a Breakout on a close above $120, the 252-session high.

Common base depth mistakes

  • Measuring from the wrong high. Start from the peak that began the base, not a minor bounce inside it.
  • Mixing closes and intraday lows. Pick one method and stick with it, or depth comparisons drift.
  • Judging depth without market context. A 30% base during a broad correction is different from a 30% base in a calm market.
  • Buying the right side too early. A deep base that has not recovered toward its high has overhead supply still ahead of it.
  • Assuming shallow means strong. A shallow base under falling moving averages is still a weak setup.

After-close base depth checklist

  1. Mark the left-side high and the lowest low, then calculate the depth.
  2. Measure each pullback and check that they get smaller.
  3. Note how far price is from the 252-session high. Within 5% is where TraderSight’s proximity rule qualifies.
  4. Confirm price is above the 50-day average.
  5. Size from the stop with the position size calculator, and see how setups progress from Developing to Ready.

Base depth: common questions

Related

See this on a real chart

Check the pattern against a real daily chart and its setup explanation. Browse ranked setups and look up additional stocks free, with results one session delayed. No card required.

Look up a stock free

Educational only. Not investment advice.